Skip to content 
Ready to talk vinyl for your University City home? Book a free walkaround with our crew and we’ll log the profile, photograph every gable and soffit, and email a written line-item bid inside 48 hours. Call (314) 618-8888 to lock in a time.
Your University City home probably wears brick — most do. But the gable ends, dormer cheeks, porch ceilings, soffit runs, and detached-garage walls are wood, and after a couple of tennis-ball hail seasons plus the shade of Forsyth’s tree canopy those wood elements crack, warp, and peel. Vinyl siding in University City, MO gives you a low-maintenance way to re-wrap post-WWII ranches north of Olive or replace tired wood details without touching the brick — Top Quality Exteriors scopes every job to your home’s era and the street it sits on.
Every panel we install matches your home’s profile — double-4 or double-5 lap, dutchlap, or board-and-batten — so replacements read as the original wall, not a patchwork. We factor Class 4 impact ratings for the 83-hail-report years, insulated foam backers for the north-of-Olive ranches that ran on 1950s wall assemblies, and fade-resistant color technology so a west-facing gable in Parkview Gardens still matches after ten summers. For landmark blocks near the Loop where vinyl won’t pass historic review, our fiber cement siding for University City fits.
Panel fit-out starts with a walkaround: we log the existing profile, weave joints, corner posts, F- and J-channels, and any custom trim around the porch ceiling or dormer cheek. Then we tear off, inspect the sheathing for hail bruising or hidden rot at butt joints, and replace whatever OSB has softened before house wrap goes back on. On post-WWII stock north of Olive the wall cavity often lacks any real thermal break, so we spec insulated foam-backed panels — that contoured EPS backer picks up an R-value between 2.0 and 4.0 and dampens road noise from I-170. South-of-Delmar historic blocks are different: vinyl typically only earns its keep on the garage, the dormer cheek, a rear addition, or a detached carriage house — never the primary brick façade. Every crew we run is registered with the City of University City as the building code requires, so permits at the fourth-floor Planning & Zoning counter don’t stall. For the full picture of scope, sequencing, and warranty, see our siding installation in University City.
Every University City vinyl job runs through the same five steps in the same order, on the same schedule. It keeps the crew accountable and gives you a written trail — permit pull, tear-off, sheathing check, install, walk. Here’s what each covers.
We meet you on-site, log the existing panel profile, corners, and trim runs. We photograph every gable, dormer, and soffit for the file. Then we send a written line-item bid, fast.
We pull the reside permit for you at University City’s Planning counter under our registered contractor number. If you sit within 300 feet of a landmark we file HPC review too.
We strip failing panels, house wrap, and punky trim in one pass. Sheathing gets probed for hail bruising and soft spots at every butt joint. Rotten OSB is swapped before rewrap.
New starter strip, corner posts, and F-channels go on square and plumb. Panels hang on a double-nail schedule with the correct expansion gap for U City swings, then trim seals.
We walk the perimeter with you and check every panel, joint, trim piece under bright light. Punch-list items are fixed on the spot, not on return trip. Warranty paperwork stays.
Top Quality Exteriors is a BBB Accredited business with an A+ rating, licensed in Missouri and Illinois, and registered with the City of University City for building code work. Our 52+ crew carries general liability and workers’ compensation coverage on every job, so a ladder or a compressor on your Delmar-corridor sidewalk is our exposure, not yours. Founded in 2022, our team brings over seven years of industry experience to every panel that goes up.
When the walkaround shows fiber cement is the smarter call for a historic block near Ames Place or a Parkview façade, our James Hardie siding in University City covers that too — we’re a James Hardie® Alliance Program Member. Every job carries a 36-month workmanship warranty, with extended options up to a Lifetime warranty on selected products, plus manufacturer coverage tied to the exact panel line and color you pick. That paper trail matters after a spring storm.
For a typical University City project, standard vinyl runs about $2 to $6 per square foot installed, and insulated foam-backed profiles climb to $7 to $11 per square foot. That puts a full re-wrap on an 1,800-square-foot north-of-Olive ranch in the $9,000 to $15,000 window, with detached-garage and dormer-cheek jobs often landing under $4,000. Real numbers vary by profile, corner count, and how much sheathing needs to be replaced under the panels.
Compared to a full brick tuckpoint or a fiber cement re-wrap, vinyl clears the same weather job for a fraction of the ticket — and Hearth and GreenSky financing spread that out over monthly payments most homeowners already budget for. Because we tear off cleanly and pull permits under our registered contractor number, insurance restoration checks after a spring hail event tend to close without back-and-forth. Ask about pairing insulated backers with the wall.
Every credential we carry is a commitment to quality, safety, and your peace of mind — on every project, in every state we serve.
